Enabled the bi-directional features of the Digikeijs ext88 bus Status requests for module >= “Report feedback from” are reported as Feedback, below that Turnouts are reported (as of Lenz spec’s) Added option to set ‘Report feedback from’ to report Feedback and not Turnout status. When used with the DR5088RC you read back POM commands – Modern, low-loss switching external power supply.ĭR5000 can save loco settings (speed, direction and functions) when pressing the STOP button, at startup, DR5000 will readback those settings when enabled – All protocols are translated to the DR.Cmd internal protocol.Įvery Bus/Connection receives specific and relevant data from the internal protocol.
#Rocrail ds64 series
– Feedbacks from combining all buses in one series of 1-2048 – 2048 feedback, which is the total of all possible buses. – Offset +4/-4 for MultiMaus compatibility (9999 for long, Maximum short addresses to be set from 0-127) – 126 simultaneous operation / control of locos – Link: The LAN is connected and connected to a switch / hub / router. Intensity increases with the number of active inputs. – There is at least one input on the s88 bus active – The signals to Track-Out and the booster connection are ON. – The signals to Track-Out and the booster connection are off. – RX: Data is being received from the X-BUS. – RX: Data is received from the computer.
#Rocrail ds64 code
Blink Code defines the bus caused the short circuit – Power: Power supply present Programming track indicator The DR502圎XT modules or via the USB/LAN/Wifi interfaces. – Further control possible through X-BUS and/or L.NET (manual)controls, – 4 channels, per channel directly to be controlled/switched, 1 lok and 4 switches. – IR receiver compatible with Uhlenbrock IRIS and Piko DigiFern (or other RC5/36Khz remotecontrols). – The WiFi / LAN module can serve as an AP (access point) as well as a router between the DR5000 and WiFi home network (LAN). – Wifi/LAN settings can be changed via a web-interface – Protocols: Lenz XpressNet and/or L.NET-TCP/IP – Both networks can be accessed via UDP / IP and TCP / IP – bgn Wireless network via internal antenna. Can be connected to a local network via DHCP. Adjustable output eliminates the need of a programming track booster.Īutomatically switches from Track-Out to Program mode so the programming rail can also be used. – Interface for DR502圎XT modules (bi-directioneel). – Interface for Lenz-RS-Bus feedback modules. the MultiMaus boosters 10764 lan as a booster together with the DR5000! – Interface for XpressNet devices: MultiMaus, LH100 etc. – Interface for L.NET devices including boosters (rail-sync). – Interface for L.NET devices: (manual-)Controllers, Feedback modules etc. – Interface for L.NET devices (Controllers, Feedback modules etc.) – Communication with computer/control program
XpressNet – Easily Connect X-Bus Components From Lenz, CVP Including Wireless Receivers And Throttles (CVP OPS T1300) Keep Your LocoNet Clean With Separate LocoNet Connections For Your Boosters (DB150, DB210, Etc.) and Other Devices (UP5, UR92, DS64, SE8C, BDL168, Etc…) POM Read Back When Used With The Digikeijs DR5088RC RailCom – Use Id tags on your JMRI, Rocrail, Etc…, Panel To See What Loco Is In A Specific Block – Great For Dispatchers And Hidden Staging Yards When Used With The Digikeijs DR5088RC
#Rocrail ds64 Pc
On Board Easy Stop & Go Buttons For Track PowerĮasy To Use GUI For Your PC – Easy Decoder Programming, Setting Board Id’s, Monitoring Occupancy Feedback, Booster Stats ex. IR Sensor – For Infrared Equipped Throttles Programming Track – Drive On/Drive Off – No Special Wiring Needed Programming Track Output – Easily Adjust Your Programming Track Voltage (No Extra Booster Needed For Sound Equipped Engines)
LAN Port Built In – Easy Computer and Router Networking WiFi Built In – Smartphones, Tablets, WiFi Throttles (Roco Z71 Phone and Tablet Apps & WLANmaus) The power supply is equipped with a 2.5mm angled plug and a US power plug. Roco – Including all web, smart phone and tablet apps. $410 – Total For Others without Shipping!ĭigitrax – All current Digitrax products – Simplex with firmware starting with 1.6.2ĬVP Products – Xpressnet Lenz compatible receivers, throttles, etc… $45 – Average North American Power Supply $60 – Average USB Computer Connection Device Why is this such a great deal? Let’s Compare: Clear LED displays and integrated USB, LAN and WIFI! The first DCC Command Station with all imaginable connectors combined in one device.
0 kommentar(er)
